. .
. .10WIRING CONNECTIONSH1/6 BROWN Wire Accessory Output (Heater /AC Output)Connect the BRO
. .11WIRING CONNECTIONSH2/4 BROWN Wire (Horn Output)The BROWN wire will provide a (-) negat
. .12WIRING CONNECTIONSH5/2 BROWN/RED (Positive Safety Shut Down or Brake Input)This wire p
. .13WIRING CONNECTIONSH5/3 THIN BLACK Wire ( Remote Start Enable or Nuetral SafetyInput)Wh
. .14WIRING CONNECTIONSH5/7 VIOLET (Positive Door Input) (Must be used for manualtransmiss
. .15WIRING CONNECTIONSPositive Oil Sensor Connections: +2volts to + 3volts will show ONth
. .16WIRING CONNECTIONSVACUUM OPERATED DOORLOCKING SYSTEM:TYPICAL OF MERCEDES BENZAND AUDI.L
. .17WIRING CONNECTIONSH7/2 BLACK/VIOLET (Timer Control Channel 6 ProgrammableOutput)The BL
. .18WIRING CONNECTIONSH7/4 BLACK/WHITE (Dome Light Supervision Output)The BLACK/WHITE wire
. .19WIRING CONNECTIONSH7/7 RED/WHITE (Channel 3 Trunk Output)The RED/WHITE wire will provi
. .For most vehicles we have a T-Harness available to make yourremote starter installation q
. .20WIRING CONNECTIONS7/9 ORANGE/WHITE (Ground Output When Disarmed)The ORANGE/WHITE wire
. .21PROGRAMMING AND TESTINGA. Manual Transmission: When you are in manual transmission gear
. .22Exit: Turn the ignition switch to the OFF position, or leave it for 15seconds. 3 long
. .23PROGRAMMINGALARM FEATURE #1 PROGRAMMING CHARTOne Chirp withPress One LED PulseTransmitt
. .24PROGRAMMINGALARM FEATURE #2 PROGRAMMING CHARTOne Chirp withPress One LED PulseTransmitt
. .25PROGRAMMINGExit: Turn ignition switch to the on position, or leaveit for 15 seconds. 3
. .26PROGRAMMINGChannels 4 (5 / 6) Timer Control Output Programming.1. Turn the Ignition swi
. .27PROGRAMMINGREMOTE START FEATURE PROGRAM MODE.START FEATURE. # 1 PRORAMMING:1. Turn the
. .28PROGRAMMINGExit: Turn Ignition to ON position, or leave it for 15 seconds. 3 longchir
. .29PROGRAMMING6 +3 Hour Time 2 Hour TimeStart Start7 + The Vehicle The Vehicle has Bui
. .TABLE OF CONTENTS3INSTALLATION DIAGRAM ...
. .30PROGRAMMINGExit: Press the button on the transmitter 3 long chirps and 3 parkinglight
. .31PROGRAMMING4. If the crank time is too long, (Engine already successfully running, whil
. .32PROGRAMMING3. If the crank time is too long, (The engine is successfully running, while
. .33PROGRAMMING2. If the crank time is too long, (Engine already successfully running, whil
. .34PROGRAMMINGTo Exit: Turn Ignition to the on position, or leave it for 15 seconds. 3long
. .35PROGRAMMINGTESTING YOUR INSTALLATIONLEDFlashes Shutdown Mode7 Tach. Signal has not been
. .366. Start the vehicle using the remote transmitter.a. If the starter does not engage, th
. .372. Connect the THIN BLACK Neutral Safety Switch wire (H5/3) to thisreference wire.NOTE:
. .38Method 2 will allow the safety required for the remote start unit and preventthe vehicl
. .39TESTING YOUR INSTALLATIONNote: A second 4003 series diode may be required to maintain t
. .TABLE OF CONTENTS4 2 Steps Door Unlock Wire ConnectionType A Positive Switched Door L
. .WARRANTYBulldog Warranty InformationAll Bulldog models have a Limited Lifetime Warranty o
. .
. .TABLE OF CONTENTS5This remote starter with keyless entry system is designed to beinstalle
. .6IMPORTANT NOTICECOMPONENTS 1- Main Control Module 1- Five Button LCD RemoteTransmitter
. .7INSTALLATION DIAGRAM6 Pin WhiteConnector forDoor Lock andDoor UnlockConnection6
. .8WIRING HARNESSESKeep all wiring away from moving engine parts, exhaust pipes and high-te
. .9WIRING CONNECTIONSH1: 6-PIN HEAVY GAUGE WIRING CONNECTIONS:Remember that the system is
Comments to this Manuals